Awarded as the best online publication by CIDC

Low Cost Housing

Low Cost Housing is a new concept which deals with effective budgeting and following of techniques which help in reducing the cost construction through the use of locally available materials along with improved skills and technology without sacrificing the strength, performance and life of the structure.There is huge misconception that low cost housing is suitable for only sub standard works and they are constructed by utilizing cheap building materials of low quality.The fact is that Low cost housing is done by proper management of resources.Economy is also achieved by postponing finishing works or implementing them in phases.

Building Cost
The building construction cost can be divided into two parts namely:
Building material cost : 65 to 70 %
Labour cost : 65 to 70 %
Now in low cost housing, building material cost is less because we make use of the locally available materials and also the labour cost can be reduced by properly making the time schedule of our work. Cost of reduction is achieved by selection of more efficient material or by an improved design.

Areas from where cost can be reduced are:-
1) Reduce plinth area by using thinner wall concept.Ex.15 cms thick solid concrete block wall.

2) Use locally available material in an innovative form like soil cement blocks in place of burnt brick.

3) Use energy efficiency materials which consumes less energy like concrete block in place of burnt brick.

4) Use environmentally friendly materials which are substitute for conventional building components like use R.C.C. Door and window frames in place of wooden frames.

Advertisements

5) Preplan every component of a house and rationalize the design procedure for reducing the size of the component in the building.

6) By planning each and every component of a house the wastage of materials due to demolition of the unplanned component of the house can be avoided.

7) Each component of the house shall be checked whether if it’s necessary, if it is not necessary, then that component should not be used.

Cost reduction through adhoc methods
Foundation
Normally the foundation cost comes to about 10 to 15% of the total building and usually foundation depth of 3 to 4 ft. is adopted for single or double store building and also the concrete bed of 6″(15 Cms.) is used for the foundation which could be avoided.

It is recommended to adopt a foundation depth of 2 ft.(0.6m) for normal soil like gravely soil, red soils etc., and use the uncoursed rubble masonry with the bond stones and good packing. Similarly the foundation width is rationalized to 2 ft.(0.6m).To avoid cracks formation in foundation the masonry shall be thoroughly packed with cement mortar of 1:8 boulders and bond stones at regular intervals.

It is further suggested adopt arch foundation in ordinary soil for effecting reduction in construction cost up to 40%.This kind of foundation will help in bridging the loose pockets of soil which occurs along the foundation.

In the case black cotton and other soft soils it is recommend to use under ream pile foundation which saves about 20 to 25% in cost over the conventional method of construction.

Advertisements

Plinth
It is suggested to adopt 1 ft. height above ground level for the plinth and may be constructed with a cement mortar of 1:6. The plinth slab of 4 to 6″ which is normally adopted can be avoided and in its place brick on edge can be used for reducing the cost. By adopting this procedure the cost of plinth foundation can be reduced by about 35 to 50%.It is necessary to take precaution of providing impervious blanket like concrete slabs or stone slabs all round the building for enabling to reduce erosion of soil and thereby avoiding exposure of foundation surface and crack formation.

Walling
Wall thickness of 6 to 9″ is recommended for adoption in the construction of walls all-round the building and 41/2 ” for inside walls. It is suggested to use burnt bricks which are immersed in water for 24 hours and then shall be used for the walls

Rat – trap bond wall
It is a cavity wall construction with added advantage of thermal comfort and reduction in the quantity of bricks required for masonry work. By adopting this method of bonding of brick masonry compared to traditional English or Flemish bond masonry, it is possible to reduce in the material cost of bricks by 25% and about 10to 15% in the masonry cost. By adopting rat-trap bond method one can create aesthetically pleasing wall surface and plastering can be avoided.

Concrete block walling
In view of high energy consumption by burnt brick it is suggested to use concrete block (block hollow and solid) which consumes about only 1/3 of the energy of the burnt bricks in its production. By using concrete block masonry the wall thickness can be reduced from 20 cms to 15 Cms. Concrete block masonry saves mortar consumption, speedy construction of wall resulting in higher output of labour, plastering can be avoided thereby an overall saving of 10 to 25% can be achieved.

Soil cement block technology
It is an alternative method of construction of walls using soil cement blocks in place of burnt bricks masonry. It is an energy efficient method of construction where soil mixed with 5% and above cement and pressed in hand operated machine and cured well and then used in the masonry. This masonry doesn’t require plastering on both sides of the wall. The overall economy that could be achieved with the soil cement technology is about 15 to 20% compared to conventional method of construction.

Doors and windows
It is suggested not to use wood for doors and windows and in its place concrete or steel section frames shall be used for achieving saving in cost up to 30 to 40%.Similiarly for shutters commercially available block boards, fibre or wooden practical boards etc., shall be used for reducing the cost by about 25%.By adopting brick jelly work and precast components effective ventilation could be provided to the building and also the construction cost could be saved up to 50% over the window components.

Lintals and Chajjas
The traditional R.C.C. lintels which are costly can be replaced by brick arches for small spans and save construction cost up to 30 to 40% over the traditional method of construction. By adopting arches of different shapes a good architectural pleasing appearance can be given to the external wall surfaces of the brick masonry.

Roofing
Normally 5″(12.5 cms) thick R.C.C. slabs is used for roofing of residential buildings. By adopting rationally designed insitu construction practices like filler slab and precast elements the construction cost of roofing can be reduced by about 20 to 25%.

Filler slabs
They are normal RCC slabs where bottom half (tension) concrete portions are replaced by filler materials such as bricks, tiles, cellular concrete blocks, etc.These filler materials are so placed as not to compromise structural strength, result in replacing unwanted and nonfunctional tension concrete, thus resulting in economy. These are safe, sound and provide aesthetically pleasing pattern ceilings and also need no plaster.

For more on filler materials check Filler Materials Used in Concrete

Jack arch roof/floor
They are easy to construct, save on cement and steel, are more appropriate in hot climates. These can be constructed using compressed earth blocks also as alternative to bricks for further economy.

Ferrocement channel/shell unit
Provide an economic solution to RCC slab by providing 30 to 40% cost reduction on floor/roof unit over RCC slabs without compromising the strength. These being precast, construction is speedy, economical due to avoidance of shuttering and facilitate quality control.

Finishing Work
The cost of finishing items like sanitary, electricity, painting etc., varies depending upon the type and quality of products used in the building and its cost reduction is left to the individual choice and liking.

Advertisements

Conclusion
The above list of suggestion for reducing construction cost is of general nature and it varies depending upon the nature of the building to be constructed, budget of the owner, geographical location where the house is to be constructed, availability of the building material, good construction management practices etc. However it is necessary that good planning and design methods shall be adopted by utilizing the services of an experienced engineer or an architect for supervising the work, thereby achieving overall cost effectiveness to the extent of 25% in actual practice.

Share this post

Kanwarjot Singh

Kanwarjot Singh is the founder of Civil Engineering Portal, a leading civil engineering website which has been awarded as the best online publication by CIDC. He did his BE civil from Thapar University, Patiala and has been working on this website with his team of Civil Engineers.

If you have a query, you can ask a question here.

206 comments on "Low Cost Housing"

1 4 5 6 7 8 10
Merwyn says:

Hello Sir,
The cost of house construction in Goa is rising everyday.your website was a ray of hope. Do you take contratcts for such houses if yes then please could i see some pics.

G JANAKI says:

For a suit of length22ft width 18ft in a small countryside piligrimage centre at a low cost approximately three lacs. kindly provide plan & estimate janaki

kago says:

what are the various low cost housing material which is available in rural area….

ruban says:

i want to know more about low cost technology. Can you advice.

Chytra says:

i want to know more about low cost technology with cost for 15/30 site for 1 floor. Can you advice.

Swati Ranganathan says:

i am an architecture student.
pls cn u send me info on joshi swastik bond.
i need them for my presentation.

mc fundi says:

let me know a simple technologies for me as local burnt brick producer.in order to control shape of a brick.

Habil Ahmad says:

so helpfulllllllll material,tnks sir

Prasun kumar says:

wonderful ideas!!!!!
but could have been more technical.

Sanchita Chowdhury says:

I would like to know about low cost housing in detail, also the availability of matreial in West Bengal and its costs etc. Please let me know and the contact details.
thanks.

Sanchita

AR.Sharma says:

you can go for compressed earthen blocks, they cost very less and are very strong and durable, locally available stone can be used also site made materials like ferro cement, or concrete blocks

anantharama says:

sir recently ihave read in some news paper about low cost housing.i have learnt that asingle bed room house can be constructed at cost rs 175000(.of course portable house.)pl. advice me

Narendra says:

Looking for low cost house construction in rural area near Sirsi (Uttara Kannada district). Can some one suggest me, how to go about?

sanjay bhargava says:

i am interested in constructing a 1500 sq feet,low cost house near Jaipur,Rajasthan.Can you please help

Krishnakumar says:

Dear sir, i feel so much relaxed after going through this article. Thank u. It will be a great help if you give the plan and advice for my 1500ft low cost house in kerala.

raveesha p says:

sir/medum plz send me the detaild report on the fillar slab plz send me

venu gopal says:

super thank uuuuuuuuuuuuuuuuu

susant panigrahi says:

hi,
i am interested to know if u have any details about fire proof thatched roof,plz send it.
thanks,
susant

suresh says:

Dear sir,
I am planning for a low cost house in bangalore around 20 Squares, kindly help me the names and numbers who can help me

Mallesh says:

Kindly advise I like to build 100 small room like hotel with kitchen in one story in 2acre land. I like to build and demolish after 5years to build a 4 stories building. Kindly advise I like to spend only 1lakh per unit I ready to use the Junksheet to get it up and running.

AR.Sharma says:

a good article even planned structural design can reduce cost usage of t-beams etc can reduce cost of housing…

1 4 5 6 7 8 10

Leave a Reply

Your email address will not be published. Required fields are marked *

Ask a question