# Mix Design M-50 Grade

Posted in Mix Design | Email This Post |The mix design M-50 grade (Using Admixture –Sikament) provided here is for reference purpose only. Actual site conditions vary and thus this should be adjusted as per the location and other factors.

**Parameters for mix design M50**

Grade Designation = M-50

Type of cement = O.P.C-43 grade

Brand of cement = Vikram ( Grasim )

Admixture = Sika [Sikament 170 ( H ) ]

Fine Aggregate = Zone-II

**Sp. Gravity**

Cement = 3.15

Fine Aggregate = 2.61

Coarse Aggregate (20mm) = 2.65

Coarse Aggregate (10mm) = 2.66

Minimum Cement (As per contract) =400 kg / m^{3}

Maximum water cement ratio (As per contract) = 0.45

**Mix Calculation: –**

1. Target Mean Strength = 50 + ( 5 X 1.65 ) = 58.25 Mpa

2. *Selection of water cement ratio:-*

Assume water cement ratio = 0.35

3. *Calculation of water: –*

Approximate water content for 20mm max. Size of aggregate = 180 kg /m^{3} (As per Table No. 5 , IS : 10262 ). As plasticizer is proposed we can reduce water content by 20%.

Now water content = 180 X 0.8 = 144 kg /m^{3}

4.

*Calculation of cement content:-*

Water cement ratio = 0.35

Water content per cum of concrete = 144 kg

Cement content = 144/0.35 = 411.4 kg / m

^{3}

Say cement content = 412 kg / m

^{3}(As per contract Minimum cement content 400 kg / m

^{3})

Hence O.K.

5. Calculation for C.A. & F.A.: [ Formula’s can be seen in earlier posts]-

Volume of concrete = 1 m^{3}

Volume of cement = 412 / ( 3.15 X 1000 ) = 0.1308 m^{3}

Volume of water = 144 / ( 1 X 1000 ) = 0.1440 m^{3}

Volume of Admixture = 4.994 / (1.145 X 1000 ) = 0.0043 m^{3}

Total weight of other materials except coarse aggregate = 0.1308 + 0.1440 +0.0043 = 0.2791 m^{3}

Volume of coarse and fine aggregate = 1 – 0.2791 = 0.7209 m^{3}

Volume of F.A. = 0.7209 X 0.33 = 0.2379 m^{3} (Assuming 33% by volume of total aggregate )

Volume of C.A. = 0.7209 – 0.2379 = 0.4830 m^{3}

Therefore weight of F.A. = 0.2379 X 2.61 X 1000 = 620.919 kg/ m^{3}

Say weight of F.A. = 621 kg/ m^{3}

Therefore weight of C.A. = 0.4830 X 2.655 X 1000 = 1282.365 kg/ m^{3}

Say weight of C.A. = 1284 kg/ m^{3}

Considering 20 mm: 10mm = 0.55: 0.45

20mm = 706 kg .

10mm = 578 kg .

Hence Mix details per m^{3}

Increasing cement, water, admixture by 2.5% for this trial

Cement = 412 X 1.025 = 422 kg

Water = 144 X 1.025 = 147.6 kg

Fine aggregate = 621 kg

Coarse aggregate 20 mm = 706 kg

Coarse aggregate 10 mm = 578 kg

Admixture = 1.2 % by weight of cement = 5.064 kg.

**Water: cement: F.A.: C.A. = 0.35: 1: 1.472: 3.043 **

**Observation: –**

A. Mix was cohesive and homogeneous.

B. Slump = 120 mm

C. No. of cube casted = 9 Nos.

7 days average compressive strength = 52.07 MPa.

28 days average compressive strength = 62.52 MPa which is greater than 58.25MPa

Hence the mix accepted.

We are thankful to Er Gurjeet Singh for this valuable information.

Sir,

It is very useful to me. I am working in a PSC sleeper industry and we produce PSC Slab of 6.1m span also.

thank you and wishing you a very happy dasahra.

It is very useful to my study . I am studying in B.E., (civil)

hi

this is MKC

It is very wonderful see to your mix design.But still some of the things are missing there that u are preparing ur mix design by considering some of the indian standard.

In any IS will not say 20% reduction of water and in the ending stage increasing 2.5%

Dear Gurjeet Singh

How it is possible

on Assume water cement ratio = 0.35(only 20% water reduction

according aginest superplatiser) & Cement Content 422 Kg/m3

u have acchived strength of M-50 with Micro Silica ?

Plz. reviwe it as u feel comfort

Hi, As we are providing plasticizers which means we are increasing the plasticity or fluidity of the concrete. So we can reduce the amount of water required. It is basically done to increase the workability which itself reduce the amount of water required. If we don’t use plasticizer then the amount of water will be increased so as to get the desired workability. And for starting the mix design we have to assume some water cement ratio so as to calculate the quantities of the cement and water.Depending upon the amount of workability required and the site conditions we assume it.

Please let me know if u still need any clarification

Yes it is true we have acheived M-50 strength with with 422kg cement amount.

please elaborate your question regarding acheiving strength with micro silica

hi

it is very good to see u mix design.

i have one question for u, if i used cement of grade 53 – o.p.c inseded of grade 43 -o.p.c used , we want to used fly ash and 400 k.g of cememt, can you give us the detail mix design for M-50 grade of concrete.

sir v r doing a project by using M50 grade of concrete, OPC 43grade.

Without using any admixtures. can u pls tell me how to calculate the

water cement ratio and full details about the mix design.

Thank u

sir,

we are constructing a road with dry Lean concrete(150 mm thk. top layer over a 200mm brick soling) , 13 km. long in sundarban island.pls. guide us on the matter that how to do the rolling over DLC with a 8 ton static roller and how to determine the OMC of the DLC.

Thank u.

if you could please tell me the number 1 and 2 aggregate to mm i mean nubmer 1 aggregate is equel to ?mm

if you could please me give more tip regarding the mix.

sir

these are very good notes but sir i want that it should be gernal. because if you sent me gernal notes for concrete mix design i will be very thankful to you for this kind action

thanks

dear sir,

how to fix proportion on concrete? why add to the fly ash

I need mix design procedure for Zero near slump concrete for mfg Precast concrete interlocking pavements of M50 grade. This paper deals with .5 W/C

Sir, I need mix design procedure for concrete( with OPC)without fly ash; in two cases,(1)having crushed sand as fine agreegate and M1, M2 coarse aggregates,and (2) having both crushed sand and natural sand (river sand) as fine aggregates with M1, M2 coarse aggregates, for any grade of concrete

Dear sir we are using M:40 and M:60 with OPC cement, is it possible to achive M:40 with PPC cement.

Respecred Sir

i shall be highly oblige if you kindly send M60 GRADE CONCRETE mix design as early as possible

Thank you very much for many kinds of mix design. I am working with Chinese engineers and they are using Chinese Code in Concrete. I want to know the different code used in Indian Standard AND Chinese standard. They use C10, C15, C20, C25, C30 and so on. Could you please compare IS and that of Chinese.

Thank you.

hi your mix design is based on w. c. ratio so upload this also without admixtures

Whate is W4 water impermiable concrete?

please forward C40 W4 grade concrete

Please provide me with the information regarding–

1. M70 amd M75 concrete compostion

2. M70 and M75 concrete uses

3. M70 amd M75 concrete strength

hi guys… I am currently in need of design manual for The FIBRE REINFORCED CONCRETE.. can any one please help me .