# Mix Design M-40 Grade

Posted in Mix Design | Email This Post |The mix design M-40 grade for Pier (Using Admixture – Fosroc) provided here is for reference purpose only. Actual site conditions vary and thus this should be adjusted as per the location and other factors.

**Parameters for mix design M40**

Grade Designation = M-40

Type of cement = O.P.C-43 grade

Brand of cement = Vikram ( Grasim )

Admixture = Fosroc ( Conplast SP 430 G8M )

Fine Aggregate = Zone-II

Sp. Gravity Cement = 3.15

Fine Aggregate = 2.61

Coarse Aggregate (20mm) = 2.65

Coarse Aggregate (10mm) = 2.66

Minimum Cement (As per contract) = 400 kg / m^{3}

Maximum water cement ratio (As per contract) = 0.45

**Mix Calculation: –**

1. Target Mean Strength = 40 + (5 X 1.65) = 48.25 Mpa

2. *Selection of water cement ratio:-*

Assume water cement ratio = 0.4

3. *Calculation of cement content: –*

Assume cement content 400 kg / m^{3}

(As per contract Minimum cement content 400 kg / m^{3})

4. *Calculation of water: –*

400 X 0.4 = 160 kg Which is less than 186 kg (As per Table No. 4, IS: 10262)

Hence o.k.

5. Calculation for C.A. & F.A.: – As per IS : 10262 , Cl. No. 3.5.1

V = [ W + (C/S_{c}) + (1/p) . (f_{a}/S_{fa}) ] x (1/1000)

V = [ W + (C/S_{c}) + {1/(1-p)} . (ca/S_{ca}) ] x (1/1000)

Where

V = absolute volume of fresh concrete, which is equal to gross volume (m^{3}) minus the volume of entrapped air ,

W = mass of water ( kg ) per m^{3} of concrete ,

C = mass of cement ( kg ) per m^{3} of concrete ,

S_{c} = specific gravity of cement,

(p) = Ratio of fine aggregate to total aggregate by absolute volume ,

(fa) , (ca) = total mass of fine aggregate and coarse aggregate (kg) per m^{3} of

Concrete respectively, and

Sfa , Sca = specific gravities of saturated surface dry fine aggregate and Coarse aggregate respectively.

As per Table No. 3 , IS-10262, for 20mm maximum size entrapped air is 2% .

Assume F.A. by % of volume of total aggregate = 36.5 %

0.98 = [ 160 + ( 400 / 3.15 ) + ( 1 / 0.365 ) ( Fa / 2.61 )] ( 1 /1000 )

=> Fa = 660.2 kg

Say Fa = 660 kg.

0.98 = [ 160 + ( 400 / 3.15 ) + ( 1 / 0.635 ) ( Ca / 2.655 )] ( 1 /1000 )

=> Ca = 1168.37 kg.

Say Ca = 1168 kg.

**Considering 20 mm : 10mm = 0.6 : 0.4**

20mm = 701 kg .

10mm = 467 kg .

Hence Mix details per m^{3}

Cement = 400 kg

Water = 160 kg

Fine aggregate = 660 kg

Coarse aggregate 20 mm = 701 kg

Coarse aggregate 10 mm = 467 kg

Admixture = 0.6 % by weight of cement = 2.4 kg.

Recron 3S = 900 gm

**Water: cement: F.A.: C.A. = 0.4: 1: 1.65: 2.92 **

**Observation: –**

A. Mix was cohesive and homogeneous.

B. Slump = 110mm

C. No. of cube casted = 12 Nos.

7 days average compressive strength = 51.26 MPa.

28 days average compressive strength = 62.96 MPa which is greater than 48.25MPa

Hence the mix is accepted.

We are thankful to Er Gurjeet Singh for this valuable information.

sir, i want the mix design for m40 concrete which is prepared by replacing 2% of cement by silica fume

Dear sir,

please give me the strength of different grade of concrete

M20 M10 M15 M30

sir, i want the mix design for m50 concrete which is quantity 400 m3 & m40 concrete which is quantity 500 m3

Dear sir,

please give me the strength of different grade of concrete and the mix design for m40 concrete ( 500m3) , m50 concrete ( 600m3) , m60 ( 700m3) quantity. thank you

sir in the above article it has been given that 12 cubes are casted with 400 kg of cement..may i know the size of each cube??

150mm*150mm*150 mm

sir

sir i want to know about the increase of compressive sterngth in different grade what is the ratio the cement should less conumed

With out Admixture is it possible to get M40 target strength? Ad mixture roles in concreat.

how much cement required from m25 to m40,if we want to change the concrete mix in site immidiatly.gsrao

I’m extremely pleased to go thro these sites. I would love to study such designs often.

Sir, we need a mix design to cast Interlocking paver blocks of M-50 Grade. We have three kind of material, (1) Stone Dust with 6 mm (2) 10-16 mm (3) 20 mm. We are using ultratech 53 grade cement. We have tried with 20 mm material, but the side finish of Paver block was not satisfactory. So now we are not using 20 mm but in this combination we could not get m-50 strength. So please suggest me the best mix design for this. It will be helpful for me. Thanking you, Regards,

sir,

plz give me the mix design ratio all cement for 43 grade.

dear sir,

please give me a table of your 10 mpa to 25mpa mixes.

thanking you.

i want to make concrete blocks to a certain standard.

dear sir.

please conform me for the calculation of target strength send teh formula to me

plz give me the mix design ratio for grade 40

Pls. give me M-45 mix design…. in details.

Sir, we are making interlocking paver blocks of M40 grade by using cement of 53 grade, blast furnace slag, aggregate of 1/4 grade(6-8 mm) and dust. we are using rubber moulds and vibrator system for casting the paver blocks. Sir please send me the IS code for mix design of paver blocks.

Thank you sir

Give me M200 concrete mix design procedur.

dear sir,

pls.give me the proportions of cement,sand,aggregate for m25,m30.m35,m40 ,m45,m50

sir give me the cement ,aggreate and water ratio in M7.5, M15 ,M20, M25, M30, M35, M40

Dear sir,

Sir i have just started the manufacturing unit of paving blocks

and fly ash brick will you please send me the design for M15,M20,

M25,M30,M35,M40 & M45 BY USING