Awarded as the best online publication by CIDC

Presentation on Reinforcing Detailing Of R.C.C Members

Presented By
Er.T.RANGARAJAN, B.E, M.Sc(struct.engg), F.I.E, FACCE, LACI, LISSE, LIASE

WHO IS AN ENGINEER?
According to USA President Herbert Hoover, who was an engineer before he became a politician, said:
The great liability of the engineer …compared to men of other professions……is that his works are out in the open where all can see them.
His acts …..step by step …are in hard substances.
He cannot bury his mistakes in the grave like the DOCTORS.
He cannot argue them into thin air…..or blame the judge…..like the LAWYERS.
He cannot, like the ARCHITECT, cover his figures with trees and vines.
He cannot, like the politicians, screen his shortcomings by blaming his opponents….and hope the people will forget. The ENGINEER simply cannot deny he did it.
If his works do not work……he is damned.

Important Points from Presentation
A design engineer’s responsibility should include assuring the structural safety of the design, details, checking shop drawing.

Detailing is as important as design since proper detailing of engineering designs is an essential link in the planning and engineering process as some of the most devasting collapses in history have been caused by defective connections or DETAILING. There are many examples explained in the book” DESIGN AND CONSTRUCTION FAILURES by Dov Kaminetzky.

Detailing is very important not only for the proper execution of the structures but for the safety of the structures.

Advertisements

Detailing is necessary not only for the steel structures but also for the RCC members as it is the translation of all the mathematical expression’s and equation’s results.

For the RCC members for most commonly used for buildings we can divide the detailing for Slabs-with or without openings.(Rectangular,circular,non-rectangular-pyramid slab,triangular etc) balcony slab, loft slab, corner slab etc

Beams – With or without openigs.(Shallow & deep beams)
Columns – (Rectangular,l-shape,t-shape, circular,octagonal,cross shape etc)
Foundations.

Detailing for gravity loads is different from the lateral loads specially for the SEISMIC FORCES.

Apart from the detailing for the above there is a different detailing required for the Rehabilitation and strengthening of damaged structures.

We will now dwell on the DETAILING OF MEMBERS FOR THE GRAVITY AND SOME CODAL DETAILINGS AS PER IS CODE IS 13920 AND IS 4326 AS REQUIRED FOR SEISMIC FORCES.

DO’S & DONOT’S FOR DETAILING
DO’S-GENERAL
Prepare drawings properly & accurately if possible label each bar and show its shape for clarity.
Cross section of retaining wall

Cross section of retaining wall which collapsed immediately after placing of soil backfill because ¼” rather than 1-1/4” dia. were used. Error occurred because Correct rebar dia was covered by a dimension line.

2. Prepare bar-bending schedule, if necessary.
3. Indicate proper cover-clear cover, nominal cover or effective cover to reinforcement.
4. Decide detailed location of opening/hole and supply adequate details for reinforcements around the openings.
5. Use commonly available size of bars and spirals. For a single structural member the number of different sizes of bars shall be kept minimum.
6. The grade of the steel shall be clearly stated in the drawing.
7. Deformed bars need not have hooks at their ends.
8. Show enlarged details at corners, intersections of walls, beams and column joint and at similar situations.
9. Congestion of bars should be avoided at points where members intersect and make certain that all rein. Can be properly placed.
10. In the case of bundled bars, lapped splice of bundled bars shall be made by splicing one bar at a time; such individual splices within the bundle shall be staggered.
11. Make sure that hooked and bent up bars can be placed and have adequate concrete protection.
bar-bending
12. Indicate all expansion, construction and contraction joints on plans and provide details for such joints.
13. The location of construction joints shall be at the point of minimum shear approximately at mid or near the mid points. It shall be formed vertically and not in a sloped manner.

DO’S – BEAMS & SLABS:
1. Where splices are provided in bars, they shall be , as far as possible, away from the sections of maximum stresses and shall be staggered.
2 Were the depth of beams exceeds 750mm in case of beams without torsion and 450mm with torsion provide face rein. as per IS456-2000.
3. Deflection in slabs/beams may be reduced by providing compression reinforcement.
4. Only closed stirrups shall be used for transverse rein. For members subjected to torsion and for members likely to be subjected to reversal of stresses as in Seismic forces.
5. To accommodate bottom bars, it is good practice to make secondary beams shallower than main beams, at least by 50mm.

Advertisements

Do’s –COLUMNS.
1. A reinforced column shall have at least six bars of longitudinal reinforcement for using in transverse helical reinforcement.-for CIRCULAR sections.
2. A min four bars one at each corner of the column in the case of rectangular sections.
3. Keep outer dimensions of column constant, as far as possible , for reuse of forms.
4. Preferably avoid use of 2 grades of vertical bars in the same element.

DONOT’S-GENERAL:
1. Reinforcement shall not extend across an expansion joint and the break between the sections shall be complete.
2. Flexural reinforcement preferably shall not be terminated in a tension zone.
3. Bars larger than 36mm dia. Shall not be bundled.
4. Lap splices shall be not be used for bars larger than 36mm dia. Except where welded.
5. Where dowels are provided, their diameter shall not exceed the diameter of the column bars by more than 3mm.
6. Where bent up bars are provided, their contribution towards shear resistance shall not be more than 50% of the total shear to be resisted. USE OF SINGEL BENT UP BARS(CRANKED) ARE NOT ALLOWED IN THE CASE OF EARTHQUAKE RESISTANCE STRUCTURES.

DETAILING OF SLABS WITHOUT ANY CUT OR OPENINGS.
The building plan DX-3 shows the slabs in different levels for the purpose of eliminating the inflow of rainwater into the room from the open terrace and also the sunken slab for toilet in first floor.

The building plan DX-A3 is one in which the client asked the architect to provide opening all round.
slabs-used-in-building

Minimum and max.reinforcement % in beams, slabs and columns as per codal provisions should be followed.

SLABS:
It is better to provide a max spacing of 200mm(8”) for main bars and 250mm(10”) in order to control the crack width and spacing.

A min. of 0.24% shall be used for the roof slabs since it is subjected to higher temperature. Variations than the floor slabs. This is required to take care of temp. differences.

It is advisable to not to use 6mm bars as main bars as this size available in the local market is of inferior not only with respect to size but also the quality since like TATA and SAIL are not producing this size of bar.

BEAMS:
A min. of 0.2% is to be provided for the compression bars in order to take care of the deflection.
The stirrups shall be min.size of 8mm in the case of lateral load resistance .
The hooks shall be bent to 135 degree.

cantilever-beam

non-prismatic-beam

grid-beam

secondary-beams

beam-reinforecement

continous-beam-reinforcement

continous-beam-reinforcement-1

non-prismatic-section-beam

cantilever-beam-projecting-from-column

sloping-beam

haunch-beam

stresses-at-corner

shear-torsion-reinforcement-beams

cantilever-beam-point-load

beam-web

beam-coloumn-junction

splice-detail-column

reduction-column-both-sides

termination-column-bars-inside-beams

exterior-beam-column-junction

column-details-EQ-region

EQ-REGION-CONTINUOUS BEAM

footing-details

reinforcement-hammer-block

trench-section

staircase-reinforcement-waist-slab

slabless-staircase

slabless-structure

DEVELOPMENT LENGTH OF BARS FOR A CONCRETE GRADE M20 &STEEL STRENGTH Fy=415

SLNO
BAR DIA.
TENSIONmm
COMPRESSION
REMARKS
1
8
376.0
301.0
2
10
470.0
376.0
3
12
564.0
451.0
4
16
752.0
602.0
5
20
940.0
752.0
6
22
1034.0
827.0
7
25
1175.0
940.0
8
28
1316.0
1053.0
9
32
1504.0
1203.0

APPROXIMATELY USE 50Xdia FOR TENSION

Advertisements

References:
1. Handbook On Concrete Reinforcement And Detailing-sp:34(s&t)-1987.
2. Manual Of Engineering & Placing Drawings For Reinforced Concrete Structures- (Aci 315-80
3. Manual Of Standard Practice –concrete Reinforcing Steel Institute.
4. Tward Board Manual For Rural Water Supply Schemes.
5. Design Principles And Detailing Of Concrete Structures. By D.S.Prakash Rao.
6. Simplified Design-rc Buildings Of Moderate Size And Height-by Portland Cement Association,Usa.
7. Design And Construction Failures By Dov Kaminetzky.
8 IS:2502-1963 Code of practice for bending and fixing of bars for concrete reinforcement.
9. IS:1893:2000.
10. IS:4326.
11. IS:456:2000
12. Reinforced hand book by Reynold.

Download the Presentation on Reinforcing Detailing Of R.C.C Members

We are thankful to Er.T.Rangarajan for enlightening some of the detailing technique for the most commonly encountered RCC members in buildings. This presentation will surely help engineers to learn the reinforcement detailing of RCC members.

Share this post

Kanwarjot Singh

Kanwarjot Singh is the founder of Civil Engineering Portal, a leading civil engineering website which has been awarded as the best online publication by CIDC. He did his BE civil from Thapar University, Patiala and has been working on this website with his team of Civil Engineers.

If you have a query, you can ask a question here.

69 comments on "Presentation on Reinforcing Detailing Of R.C.C Members"

romit varia says:

sir.. i request you to provide me stirups shaps for various cross section of r.c.c beams. i did in ma b.e project but wld like to knw de perfect shapes with reason.

Santanu Sarkar says:

Sir,
I am a civil engineer. I want to know the notation for marking of HYSD bar and MS bar in the drawing.

neelima says:

I am a civil engineer. can u tell me sections and elevations and give me one example for 30? X 40? site plan

k.muralidharan says:

Pls clarify on clear cover to be maintained in sub structure for mast max rod dia was 16mm. If cover beyond 80mm what will be the impact.

Bilal Ahmad says:

I am a Civil Engineer . I want to know that where bars of different diameters have to be spliced, then lap length will be decided on small diameter bars, How & Why????????????

mahendra says:

Hiii,,,, please provide rft details for portal frames… means where we can give overlap etc…. i will be helpfull..

vignesh says:

i am also to be easily understanding the profile cross section and theory

DINESH says:

Im looking for reinforcement detailing of semi-circular arch in residential building

raghu nandan says:

IT IS VERY GOOD ELABORATED DRAWINGS TO A ENGINEER. I AM ALSO LOOKING FOR REINFORCEMENT DETAILING OF A RAFT FOUNDATION FOR MULTI STORIED BUILDING. THANKS,

lijesh says:

i am looking for slope slab details………..

al helal says:

what is the minimum length from beam or slab lapping can be provided

aamir khan says:

Dear Greets!

I want to know the reinforcement correct detail for a footing having three Piers(Bridge piers) FOR footing size 20mx20mx1.5m. with splices details

Thanks

Shahid says:

Really very informative website.

ENGINEER DK says:

THANKS FOR GIVING BEST DESIGN FOR ALL.

JOMIDAH says:

Great work, though am still wondering how you manage to put links for both the beams and columns in some of the congested junctions as shown above. It is theoretically possible but practicality?!

sankar says:

Hi everybody,
please tell me how to calculate the Bar Bending Schedule for an arch of parabolic shape but not semicircle

aravind r patil says:

in any column-beam junction, is it advisable to make the one side of beam bars through outside of column bars? please give the details.

Engineer A.R says:

really good information for civil engineer

Engineer Ababio says:

Can some one help me with how columns starter bars are crank to receive incoming
Columns bar

Nayak P Anand 22nd Dec, 2016 says:

Thanks sir, your topic is exemplary &quite educative. Yet it may kindly be exlained regarding “the minimum L-length of column bar is 300mm and is it apllicable for bars of all diameters. what should be the actual length & how it is determined”.

Leave a Reply

Your email address will not be published. Required fields are marked *

Ask a question